2026/04/29    [°øÁö] FSP Á¦Ç° ¼­ºñ½º ¾÷¹« Á¾·á ¾È³»
2026/04/24    2026³â 5¿ù ¿¬ÈÞ ÈÞ¹« ¾È³»


Á¦Ç° ½ºÆå : FSP200-601U(12V) New Page 2
Output Voltage Min. load Max. load Load Reg. Ripple & Noise
+5Vsb 0.0A 2.0A +-5% 100mV P-P
-12V 0.0A 0.8A +-10% 120mV P-P
-5V 0.0A 0.3A +-5% 100mV P-P
+12V 0.0A 12.0A +-5% 120mV P-P
+5V 0.1A 20.0A +-5% 50mV P-P
+3.3V 0.3A 17.0A +-5% 50mV P-P

Safety
Features
¡¡
  • High efficiency
  • Low Ripple & Noise
  • Output over voltage protection
  • Short circuit protection on all outputs
  • Resettable power shut down
  • Approved by UL,CSA, TUV, NEMKO, CB & CE
  • INTERNAL 4cm fan *2
  • 100% burn-in under high ambient temperature(50¡É)
  • Vacuum-impregnated transformer
  • MTBF:100K hours at 25¡É
  • 100% Hi-pot tested
  • line input fuse protection
  • Power Factor > 0.93
  • complies with EN61000-3-2
  • AC input full range
Specifications
¡¡ ¡¡
¡¡ ¡¡
INPUT SPECIFICATIONS  ¡¡
       ¢«Input voltage:  100-240 VAC full range
       ¢«Input frequency: 47 Hz TO 63 Hz
       ¢«Inrush current: 60A cold , 90A ware at 132 VAC
       ¢«Input current: 5 amps maximum/ 115 Vrms,60 Hz;
3 amps maximum /230 Vrms,50Hz.
¡¡
OUTPUT SPECIFICATIONS ¡¡
       ¢«Over voltage protection: +5V output : 6.82V max;
+3.3V output: 4.5V max.
       ¢«Overload protection: 150% max
       ¢«Remote ON/OFF Control: The power supply shall accept a logic collector evel which will disable / enable all output voltage
(excluding +5V standby).
¡¡
GENERAL SPECIFICATIONS ¡¡
       ¢«Hold-up time: 17ms minimum at full load & nominal input voltage
       ¢«Efficiency: 65% min. at full load
       ¢«MTBF: 100,000 hours at full load at 25¡É
       ¢«Power good signal: turn-on delay 100 ms to 500 ms
¡¡

ENVIRONMENTAL SPECIFICATIONS

      ¢«Operating temperature: 0¡É to +50¡É
      ¢«Storage temperature: -20¡É to +80¡É
      ¢«Humidity: 5~95% RH
      ¢«Dielectric withstand: input / output 1800 VAC for 1 second,
input to frame ground 1800VAC for 1 second
¡¡

OutPut
¡¡
Output Voltage Min. load Max. load Load Reg. Ripple & Noise
+5Vsb 0.0A 2.0A +-5% 100mV P-P
-12V 0.0A 0.8A +-10% 120mV P-P
-5V 0.0A 0.3A +-5% 100mV P-P
+12V 0.0A 12.0A +-5% 120mV P-P
+5V 0.1A 20.0A +-5% 50mV P-P
+3.3V 0.3A 17.0A +-5% 50mV P-P

‧+3.3V & +5V total output not exceed 120W
‧+3.3V, +5V & +12V total output not exceed 180W