2026/04/29    [°øÁö] FSP Á¦Ç° ¼­ºñ½º ¾÷¹« Á¾·á ¾È³»
2026/04/24    2026³â 5¿ù ¿¬ÈÞ ÈÞ¹« ¾È³»







FSP460-60PFN
Output Voltage Min. load Max. load Load Reg. Ripple & Noise
+3.3V 0.4A 27.0A +5% - 4% 50mV P-P
+5V 3.0A 29.0A +5% - 4% 50mV P-P
+5Vsb 0.0A 2.0A +5% - 4% 50mV P-P
-5V 0.0A 0.3A ¡¾10% 120mV P-P
+12V CPU 1.0A 16.5A +5% - 4% 120mV P-P
-12V 0.0A 0.8A +9% - 5% 120mV P-P
+12V I/O 1.0A 15.0A +5% - 4% 120mV P-P
>
¡¤ Å©±â : 140 x 150 x 86 mm
¡¤ Àû¿ë±â±â : For Server & Workstation
¡¤ Watt : 460
¡¤ PFC : Active PFC
¡¤ Äð¸µÆÒ : 80mmÆÒ
¡¤ Drawing :
Drawing

 FSP460-60PFN Ãâ½ÃÀÏ : 2007-05-23 16:23:02

Safety
Features
¡¡
  • Support Intel Nocona CPU
  • High efficiency
  • Low Ripple & Noise
  • Output over voltage protection
  • Short circuit protection on all outputs
  • Resettable power shut down
  • INTERNAL 8 cm fan
  • Dual +12V output (+12V CPU,+12V I/O)
  • 100% burn-in under high ambient temperature(50¡É)
  • Vacuum-impregnated transformer
  • MTBF:100K hours at 25¡É
  • 100% Hi-pot tested
  • Line input fuse protection
  • Complies with EN61000-3-2
  • AC input full range
  • Over-current protection meet 240 VAC
¡¡
Specifications
¡¡
  • Remote ON/OFF Control:  The Power supply shall accept a logic open collector 
                                             level which will disable /enable all out put voltage
                                             (excluding +5V standby).
  • Temperature range:         operating 0¡É~50¡É storage-20¡É~+80¡É
  • Temperature coefficient:  0.01 %/¡É
  • Transient response:          Output voltage recovers in less than 1 ms max. following a 
                                                 25% load change
  • Hold-up time:                    18.0 mS minimum : at full load & nominal input voltage           
  • Dielectric withstand:         input / output 1800VAC for 1 second, 
                                                 input to frame ground 1800VAC for 1 second
  • Humidity:                          5~95% RH
  • Efficiency:                         65% min.at full load
  • Power good signal:          turn-on delay 100ms to 500ms
  • Overload protection:        150% max
  • Inrush current:                  80A cold ,120A ware at 132 VAC
  • Over voltage protection:  +5V output : 5.6V-6.5V
                                                +3.3V output: 3.8V-4.5V
                                                +12V output: 13.0-14.5V
  • Fan Noise Killer Optional
  • Voltage:                            100-240 VAC full range
  • Frequency:                        47Hz to 63Hz
  • Input current:                     9 amps maximum / 115 Vrms, 60 HZ
                                                  5 amps maximum / 230 Vrms, 50 HZ
  • Inrush current:                 50 amps cold, 50amps warm measured at 230 Vrm
  • OutPut
    ¡¡
    Output Voltage Min. load Max. load Load Reg. Ripple & Noise
    +3.3V 0.4A 27.0A +5% - 4% 50mV P-P
    +5V 3.0A 29.0A +5% - 4% 50mV P-P
    +5Vsb 0.0A 2.0A +5% - 4% 50mV P-P
    -5V 0.0A 0.3A ¡¾10% 120mV P-P
    +12V CPU 1.0A 16.5A +5% - 4% 120mV P-P
    -12V 0.0A 0.8A +9% - 5% 120mV P-P
    +12V I/O 1.0A 15.0A +5% - 4% 120mV P-P
    ‧+3.3V &+5V total output shall not exceed 200 W.
    ‧+3.3V &+5V & +12V total output shall not exceed 440W.